Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
projects:steppermotor [2013/01/06 12:23] elger |
projects:steppermotor [2013/01/06 12:31] elger |
||
---|---|---|---|
Line 14: | Line 14: | ||
The Arduino clone is just like a regular Arduino but this one has a serial port and the labeling of the ports is more like the real Atmega328 pin mapping. | The Arduino clone is just like a regular Arduino but this one has a serial port and the labeling of the ports is more like the real Atmega328 pin mapping. | ||
- | {{ :projects:steppermotor:arduino-clone.jpg?200|}} | + | {{ :projects:steppermotor:arduino-clone.jpg?200 |}} |
- | The controller board was a bit of a chalange because I tried to design it myself with the two chips that were designed specifically for this: the L297 STEPPER MOTOR CONTROLLERS[[http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00000063.pdf|L297 STEPPER MOTOR CONTROLLERS]] and the [[http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00000240.pdf|L298 Dual Full Bridge Driver]. This is no simple task if you need to do it on a single layer PCB. So in the end I just bought the simpler L298 driver board so I could get started. | + | The controller board was a bit of a chalange because I tried to design it myself with the two chips that were designed specifically for this: the [[http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00000063.pdf|L297 STEPPER MOTOR CONTROLLERS]] and the [[http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00000240.pdf|L298 Dual Full Bridge Driver]]. This is no simple task if you need to do it on a single layer PCB. So in the end I just bought the simpler L298 driver board of [[http://www.ebay.nl/itm/L298N-Based-Stepper-DC-Motor-Driver-Controller-Board-Dual-H-Bridge-For-Arduino-/160898410591?pt=LH_DefaultDomain_0&hash=item25764ae85f|e-bay]] so I could get started. |
- | {{ :projects:steppermotor:l298n_based_dual_h-bridge_controller_board.jpg?200|}} | + | {{ :projects:steppermotor:l298n_based_dual_h-bridge_controller_board.jpg?200 |}} |
The steppermotor I chose also came from e-bay, it works on 12V and it is unipolar. In the end the problem with this motor is that the wire coloring is different from any data-sheet I could find. So after a lot of searching and testing I came up with the right sequence. | The steppermotor I chose also came from e-bay, it works on 12V and it is unipolar. In the end the problem with this motor is that the wire coloring is different from any data-sheet I could find. So after a lot of searching and testing I came up with the right sequence. | ||
- | {{ :projects:steppermotor:stepper-motor.jpg?200|}} | + | {{ :projects:steppermotor:stepper-motor.jpg?200 |}} |
- | Coil A : Blue | + | Coil A : Blue | Coil B : Yellow | Coil C : Green | Coil D : Red |
- | Coil B : Yellow | + | |
- | Coil C : Green | + | The label on the motor reads: Huisitong MOTOR 42BYGH202AA 1.8 1A 0: 20110717000KU |
- | Coil D : Red | + |